Question: Does this kind of re-configurations are allowed in NetBackup. In addition to what is covered here, refer to the information above for further notes that are relevant to all cluster environments. From the NetBackup Backup, Archive, and Restore interface, select the backup image or range of images that contains the backup of the System State for this node of the cluster. Caution Used for information that will prevent a problem. Bring the NetBackup group online: scswitch -Z -g scnb-harg 5.
Note This will bring all resources online, except NetBackup. Select the available nodes containing NetBackup and add them to the Selected Nodes list. To remove an add-on service from monitoring 1. These backups can be full or incremental and are managed entirely by the NetBackup server also referred to as the NetBackup master server. It must be running on the NetBackup master server to perform any backups or restores. Click Add All to install the agent on each system in the cluster. My thought was that when the media server has to fail over, the tape drive paths will go missing and tape drives might go to a mixed mode.
Create the following files on the master server. This is called a NetBackup failover master server and as the name implies, allows the duties of the master server to failover from one of the nodes to the other if a failure occurs on the active node. OpsCenter does not require any license and is included with the NetBackup Enterprise Server and Server products. Table 2-4 discusses the different modes in which you can configure the storage unit groups. This results in a number of processes running on each machine.
If you want the NetBackup Media Server to be highly available, the robotic and tape devices must be physically connected to all the nodes that would be part of the NetBackup High Availability setup. If this happens, increase the Scheduled Backup Attempts setting to 5 or 6. These can be used with some tape devices. Move Your Career Forward with certification training in the latest technologies. Note You may observe some transient errors while the cluster is partially configured.
From the Available Systems list, select the systems to which the NetBackup service can failover. Veritas does not guarantee the accuracy regarding the completeness of the translation. However, we did not need to add the individual nodes to the hosts file of the master and media servers. However, this compatibility ceases to be supported in any configuration once the previous major version has reached its End of Support Life. If the tape device is at the end of the bus, you can attach a terminator to one of the trilink connectors to terminate the bus. For information on Veritas End of Life Policy, refer to NetBackup Master Server NetBackup Media Server NetBackup Client 8.
The corresponding actions could be described in more steps as follows: 1. NetBackup must be uninstalled, then installed again. The same type of NetBackup server must be installed on each node to which NetBackup may failover. For example, scenarios where changes are made by deletion and re-addition, or changes where multiple records are related such as, optical partner relationships , or where robots are deleted and drives in the robot need also to be deleted. NetBackup provides high-performance backups and restores for a variety of computer types. Perform the same upgrade on the inactive nodes. This service processes requests from NetBackup clients and servers.
Listed in the table below are the backup and archiving products and versions supported by OpsCenter and OpsCenter Analytics. If you have devices attached to your failover server, run the Device Discovery wizard from each node in the cluster. In the Restart group, deselect Affects the group. Copy all NetBackup databases and files on the shared disk back to their default locations. A media server is installed on a cluster just as it is in a non-clustered environment.
This allows you to back up the data to tape devices that attach directly to one or more of the nodes without going across the network. You do not need a separate Agent to collect data from PureDisk. This occurs even if the storage unit refers to a NetBackup media server running on a node of the cluster t does not currently have control of the shared disk drives. The media server must be treated as a stand-alone application on each node in the cluster. In the right-hand pane, double-click on the resource you want to remove from monitoring.
For example, when a command has the following format: command arg1 arg2 In this example, the user can use either the arg1 or arg2 variable. On each node on which NetBackup is installed, install the NetBackup Serv software on the local disk. On the first node you want to recover, reinstall Windows, including the last service pack applied before the failure. Use the version of the agent provided with NetBackup 5. Limitations of Using NetBackup with Clustering Solutions.
The daemon to be monitored for the media server is vmd. You have options to send the catalog backups to vault and you can even mail it. Contents vii Scenario 3 - Disk Only, No Volume Manager. Select the A u toSt a rt L i s t attribute. Verify you have the NetBackup Enterprise Server 5.